Results 1 to 1 of 1

Thread: ::FREE:: Maemo Flasher 3.5_2.5.2.2 ::

  1. #1
    Join Date
    Dec 2009
    Age
    32
    Posts
    1,573
    Thanks
    0
    Thanked 21 Times in 15 Posts
    Rep Power
    6

    ::FREE:: Maemo Flasher 3.5_2.5.2.2 ::

    Flasher-3.5



    NAME
    flasher-3.5 - Maemo flasher tool

    SYNOPSIS
    Usage: flasher-3.5 [OPTIONS]

    DESCRIPTION
    The flasher tool is used to flash data to the Maemo device internal
    256MB of NAND, which is where the bootloader, kernel, and rootfs (all
    of which make up the operating system) are stored. Flasher can be used
    to upgrade the firmware, wipe the Maemo device and start from scratch,
    flash certain specific components, or change a number of hardware flags.

    OPTIONS
    -F, --fiasco=ARG Location of a FIASCO image
    -k, --kernel=ARG Location of kernel image
    -n, --initfs=ARG Location of initfs image
    -r, --rootfs=ARG Location of root JFFS2 image
    --cmt-2nd=ARG Location of CMT FIASCO 2nd image
    --cmt-algo=ARG Location of CMT FIASCO algorithm image
    --cmt-mcusw=ARG Location of CMT FIASCO MCUSW image
    --cmt-no-verify Disable verification of CMT programming
    -x, --xloader=ARG Location of X-Loader image
    -s, --secondary=ARG Location of NOLO secondary bootloader image
    -2, --2nd=ARG Location of NOLO cold flasher ("2nd") image
    -u, --unpack[=ARG] Unpack a FIASCO image
    -f, --flash Load and flash all supplied images
    -l, --load Only load all supplied images
    -b, --boot[=ARG] Boot the kernel with optional cmdline
    -R, --reboot Reboot the board (e.g. after flashing NOLO)
    -i, --read-device-id Print out the device type
    -S, --serial-port=ARG Serial port used for cold flashing or "usb"
    -I, --init-port Only initialize the serial port
    -c, --cold-flash "Cold flash" the device
    -h, --hw-revision=ARG Specify product code and HW revision
    --enable-rd-mode Enable R&D mode on the device
    --disable-rd-mode Disable R&D mode on the device
    --set-rd-flags[=ARG] Set R&D mode flags on the device
    --clear-rd-flags[=ARG] Clear R&D mode flags on the device
    --query-rd-mode Query the device R&D mode status and flags
    --set-hw-revision[=ARG] Set HW revision override on device
    --flash-only=ARG Flash only certain components
    -U, --usb-device=ARG Specify USB device to use (bus:device address)


    Valid --flash-only options:
    nolo, kernel, initfs, rootfs

    Valid --set-rd-flags and --clear-rd-flags options:
    no-omap-wd
    no-ext-wd
    no-lifeguard-reset
    serial-console
    no-usb-timeout
    sti-console
    no-charging
    force-power-key


    EXAMPLES
    To flash a image to the Maemo device, open a terminal on your computer,
    then run:

    $ flasher-3.5 -F <FIASCO image> -f -R

    Replace <FIASCO image> with the firmware image you downloaded from
    Nokia. This will flash a FIASCO image to your Maemo device and reboot
    device after itís done (at which point, you can unplug the USB). The
    procedure is the same for all other image flashing components (like
    separate kernel, rootfs and eMMC images), see the option list for details.
    If you wish to do other commands than image flashing, then omit the
    -R option as rebooting Maemo device may reset given configuration change
    back to normal.

    1) To flash a kernel with separate kernel image, open a terminal on your
    computer, then run:

    $ flasher-3.5 -k <kernel zImage> -f -R

    2) If you do not have separate images, but want to flash just a part of
    the whole FIASCO image you can do so by running:

    $ flasher-3.5 -F <FIASCO image> --flash-only=rootfs -R

    This will flash just the rootfs from the FIASCO image and reboot the
    device.

    3) If you need access to the individual parts of the FIASCO image, it can
    be unpacked by running:

    $ flasher-3.5 -F <FIASCO image> -u

    Which will expand it to your current directory.

    4) To cold flash (needed usually when the bootloader has been changed) run:

    $ flasher-3.5 -c -h RX-51:<hwid> -F <FIASCO image> -S usb

    The 'hwid' in the command options is a 4-digit code that can be found from
    the type label of the device to be flashed.


    maemo_flasher-3.5_2.5.2.2.exe
    Download
    Last edited by M.Irfan; 03-23-10 at 11:21 PM.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Mkey - Smart Flasher Unlock E173Eu1 FREE
    By silent angel in forum Gsm Cdma Mobile Repairing Devices News & Updates
    Replies: 0
    Last Post: 02-22-12, 11:28 PM
  2. Micro-Box AIO V2.0.3.2 : ADDED MANY FLASHER FOR SAMSUNG FREE FOR ALLLL
    By capricorn in forum Gsm Cdma Mobile Repairing Devices News & Updates
    Replies: 0
    Last Post: 09-26-11, 06:22 PM
  3. JAF is gone, S.F.I. Flasher is ready, free beta testing until 31.12.2010
    By marvz_TG in forum J.A.F - Just Another Flasher
    Replies: 0
    Last Post: 11-30-10, 04:58 PM
  4. Free Motorola Flasher and Backup Tools
    By Dada Bahi in forum Motorola Software Repair Area
    Replies: 1
    Last Post: 09-07-09, 04:02 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •